Providence Headlines

Hewlee® Introduces Hl-300b Battery Powered Crimping Tool

 Breaking News
  • No posts were found

Hewlee® Introduces Hl-300b Battery Powered Crimping Tool

March 27
11:00 2023

HL-300B is a tool for crimping Cu/Al lugs with cables from 10-300mm2. It is powered by Li-ion, actuated by motor and controlled by MCU. With a high pressure hydraulic system, it is a perfect tool to be used in electrical construction site.

news-thu-

General Safety Rules

To work in safe conditions with this tooling, it is imperative to read carfully the directions for use and to follow the instructions it contains. if people do not respect the information writen in that instruction manual the warranty will be cancelled.

 

1.Work area safetya.Keep work area clean and clear. Cluttered or dark areas invite accidents.b.This tool is not insulated, please do not use it on live conductor.c.Please do not use or store the tool under high temperature, or one surrounding filling with corrosive fluid. Pay attention to the sealing kits becoming aging.d.Keep children and bystander away while operating the Battery powered crimping tool. Distractions will cause people to lose control.

 

2.Electrical safetye. Make sure the plug matches with the plug seat. Never try any changes on the plug.f. Do not put tool, battery and charger under a rainy or humid surroundings, it is easy to trigger an electric shock accident if any water goes into the electric system of the tool.g. Do not use electric wire to carry, pull, or to draw out the plug. The damaged or twined wire may cause an electric shock accident.h. If the charger was strongly crashed, or dropping down or any other damages happening, please do not try to repair it by themselves, send it back to the authorized service center as soon as possible. The damaged charger may cause an electric shock accident.i. The best temperature for charging is between 10℃ – 40℃. Make surethe air hole of the battery and charger are uncovered during charging.j. Please pull out the plug when meet a bad weather.k. Please do not burn the battery or make it being short-circuited, it maycause explosion.l. Keep the tool out of reach of children and other person who are not familiar with it.

 

3. Personal safetym. Stay alert, watch what people are doing and use common sense when operating the tool. Do not use the tool while people are tired or still under the influence of drugs, alcohol or medication. A moment of inattention may result in series personal injury.n. Use safety equipment. Always use safety equipment such as mask, helmet, safety cap, insulating shoes and etc to reduce the risk of personal injury.o. Dress properly. Do not wear loose clothing or jewelry. Keep their hair, clothing and gloves away from moving parts. Loose clothes jewelry or long hair can be caught in moving parts.p. Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may effect the tool operation. If damaged, have the tool repaired before use. Many accidents are caused by poorly maintained power tools.q. Please use the tool properly, the tool with correct power will do the job better and safer at the rate for which it was designed.r. Do not put their fingers into the head of the tool during operating. Thier fingers could be pinched very severely.

 
Maintenance And Servicing

The tool earns a high precise design, please use it properly and do not disassemble it by unprofessional person, otherwise we will not responsible for the problems cause by above misuse. Or we will carry out repair if the users are willing to pay for the spare parts cost.

1. Keep tool dry. Any water may corrode the tool surface, metal or electrics parts. If contact water, take out the battery and assembly it back when the tool is fully dry.2. Avoid great temperature fluctuating to the tool. Otherwise it will cause the plastic housing to be deformed, shorten the life span of the electric parts and damage the battery.3. Please do not use any chemical agent to wash the tool.4. In order to prolong the life span, please change the hydraulic oil per year.5. If the tool not used for a long time, please make sure the position stay on its starting position, clear up the tool and paint the rustproof oil both to the tool and accessories. Take out battery and put them into box and store the tool in a dry surrounding.6. The sealing kit inside the tool will be abraded in some degree after using, when the oil leaking a lot, please contact the distributor to replace the sealing kit in timely.

image9

1.Do not knock any parts of the tool, otherwise it will cause injury.2.The design of the limit screw on the head is for preventing the head from dropping or popping.3.Make sure the head was locked firmly during operation.4.The built-in safety valve goes through strict pressure test before marketing, please do not adjust the pressure by unprofessional person. If the pressure is not enough please return the tools back to the service center, The tool only can be reused after checking and testing trained person.

Understand  Tool

HL-300B is a tool for crimping Cu/Al lugs with cables from 10-300mm2.It is powered by Li-ion, actuated by motor and controlled by MCU.With a high pressure hydraulic system, it is a perfect tool to be used in electrical construction site.

1. Specification

Max. crimping force: 60KN
Crimping range: 10-300 mm2
Stroke: 17mm
Hydraulic oil: Shell Tellus T15#
Ambient temperature: -10 – 40℃
Battery: 18v 5.0Ah Li-Ion
Crimping cycle: 3s-6s(depending on the connector size)
Crimp/charger: Approx. 260 crimps (Cu150 mm2)
Charging voltage: AC 100V〜240V; 50〜60Hz
Charging time: Approx. 2 hours
OLED display: display voltage, temperature, crimping times, errors information
Accessories:
Crimping die (mm2): 10.16.25.35.50.70.95.120.150.185.240.300
Battery: 2 pcs
Charger: 1 pcs
Sealing ring of cylinder: 1 set
Sealing ring of safety valve: 1 set

2. Description of components:

Parts No.

Description

Function

1

Die holder For fixing die

2

Die For crimping, interchangeable die

3

Latch For locking/unlocking the crimping head

4

Limited screw For prevent head from dropping or popping

5

LED indicator For indicating the operating condition and battery discharging situation

6

Retaining clips For locking/unlocking die

7

A white Led light To illuminate the working area

8

Trigger For starting operation

9

Retract button For manual retracting the piston in case of an incorrect operation

10

Battery lock For locking/unlocking the battery

11

Battery For supplying power, rechargeable Li-ion(18V)

image6

image9

The battery can be used for hundreds of times, when the life span reduced obviously, change to a new battery please.

Please charging the battery in time to avoid it to be used up absolutely; otherwise it will become useless forever, if the battery not be used for a long time, it will discharge automatically. Make sure to charge it one time per/each quarter.

3. Usage of the tool:

1) First people have to check the LED indicator is light or not. If the indicator is light on for more than 5 seconds, it means no power of the battery and should change the full powered battery to settle on the tool

2) Select the right dies for the Intended application.

 Don’t operate the tool with dies.The crimping head has to be opened by pushing the latch, place two dies up and down after activating the retaining clips. Then the connecting material shall be positioned in the crimping head correctly in order to start the crimping procedure.3) A crimping process is initiated by switching the trigger. It is defined by the closing motion of the dies. The connection material is positioned in the stationary half of the crimping dies and the moving part is approaching the compression point.4) A crimping cycle is terminated when the dies contracted each other and when the maximum crimping force is reached. After the crimping cycles is completed the piston retracts automatically. Afterwards a new crimping cycle can be initiated or the crimping process can be terminated by opening the latch and remove the connecting material out of the head.

Media Contact
Company Name: Wenzhou HEWLEE Tools Co., Ltd.
Email: Send Email
Phone: +86 13758839302 (WhatsApp)
Country: China
Website: https://www.batterycrimpingtools.com/